Copper alloys for power tool and battery pack contacts
Cordless tools and battery packs combine high pulse current, vibration, heat and thousands of insertions. Use C18140 or C19400 for the current-carrying blades and tabs, NB109 or C7025 for spring terminals that must hold force when warm, and C5210 for switch and trigger springs.
Candidate grades
| C18140 | C19400 | NB109 | C7025 | C5210 | |
|---|---|---|---|---|---|
| UNS | C18140 | C19400 | C19025 | C70250 | C52100 |
| Equivalents | EN CuCrZr (low-alloyed) | EN CuFe2P / CW107C; JIS C1940; GB QFe2.5 (TFe2.5) | JASO JC400 | EN CuNi3SiMg; JIS C7025 | EN CuSn8 / CW453K; JIS C5210; GB QSn8-0.3 |
| Composition % | Cr 0.15 – 0.45, Zr 0.05 – 0.25, Si 0.005 – 0.05 | Fe 2.1 – 2.6, P 0.015 – 0.15, Zn 0.05 – 0.20, Cu ≥ 97.0 | Ni 1.0, Sn 0.90, P 0.05 | Ni 2.2 – 4.2, Si 0.25 – 1.2, Mg 0.05 – 0.30 | Sn 7.0 – 9.0, P 0.03 – 0.35, Cu + Sn + P ≥ 99.7 |
| Conductivity %IACS | 85 | ≥ 60 | 40 | ≥ 40 | ≈ 12 |
| Tensile strength MPa | 393 – 490 | 365 – 550 | 440 – 590 | 620 – 860 | 470 – 885 |
| Tempers | H04, H08 | 1/2H (H02), H (H04), EH (H06), SH (H08), ESH (H10) | 1/2H, H, EH | TM00, TM02, TM03 | 1/2H, H, EH, SH, ESH |
| Elastic modulus | 117 GPa | 121 GPa | 130 GPa | 131 GPa | 110 GPa |
| Density | 8.91 g/cm³ | 8.91 g/cm³ | 8.9 g/cm³ | 8.82 g/cm³ | 8.80 g/cm³ |
Tensile strength is the range across supplied tempers. Full composition, tempers and physical properties are on each grade page.
Matching the alloy to the part
- Pack and tool blade terminals: C18140 for the highest current, C19400 where cost leads
- Spring contacts that grip the blade: NB109, or C7025 where more force is needed in less space
- Switch, trigger and signal springs: C5210
Notes
As packs move to higher voltage and faster charging, terminal temperature becomes the limit. A more conductive or more relaxation-resistant alloy is often cheaper than a larger terminal. We can supply sample coils of two or three candidates for a comparative temperature-rise and insertion test.
Questions buyers ask
What information do you need to recommend a material for a battery terminal?
Peak and continuous current, allowed temperature rise, strip thickness, the plating, and the number of insertion cycles. A drawing helps and can be shared under a confidentiality agreement.
Need a recommendation for a specific part?
Tell us the part function, strip thickness and performance targets. We reply within one working day, and sample coils are available for comparative trials.
Material development support